Author |
Message |
|
|
|
Advert
|
Forum adverts like this one are shown to any user who is not logged in. Join us by filling out a tiny 3 field form and you will get your own, free, dakka user account which gives a good range of benefits to you:
- No adverts like this in the forums anymore.
- Times and dates in your local timezone.
- Full tracking of what you have read so you can skip to your first unread post, easily see what has changed since you last logged in, and easily see what is new at a glance.
- Email notifications for threads you want to watch closely.
- Being a part of the oldest wargaming community on the net.
If you are already a member then feel free to login now. |
|
|
2017/09/21 15:41:27
Subject: Translucent Sculpey & LED's
|
|
Sneaky Kommando
|
Has anyone every played around with Translucent polymer clay's? I'm thinking about sculpting out a hollow form and lighting it internally with some LED's but the sculpey appears to cure very opaque and i'm afraid that the lighting will be lost unless it's in a dark room.
Also, if anyone could recommend a solid tutorial for some basic LED work, I would be greatly appreciative. I'm just trying to do something simple for now with an LED strip connected to a 12v battery and a little switch. Still new to all this but i've seen all sorts of stuff about special connectors, transistors, and transformers. Do I need all of that stuff if i'm just doing a simple strand with an on / off switch?
|
|
|
|
|
2017/09/23 04:58:12
Subject: Translucent Sculpey & LED's
|
|
Utilizing Careful Highlighting
|
The easiest thing to do is ordering LED assemblies already wired together from a site like modeltrainsoftware.com instead of trying to put together your own. Then you just drill out the necessary parts of models and glue it in.
If you just want to make a light turn on with a switch then as long as you have the LED attached to a resistor (a little cylinder on one of the wires) you'll be fine.
|
|
|
|
2017/09/23 05:16:30
Subject: Translucent Sculpey & LED's
|
|
[MOD]
Making Stuff
|
Yeah, the 'translucent' sculpey is only translucent when it's very thin. Might still work with a bright enough LED, but would need some experimentation.
|
|
|
|
|
2017/09/23 12:05:08
Subject: Translucent Sculpey & LED's
|
|
Anti-Armour Swiss Guard
|
I had a friend who sculpted little mushrooms out of sculpey (it was a fluoro yellow coloured one) which he embedded LEDs into - bright white ones.
They were surrounded by the material, so survived the oven firing, but when wired up to the power supply, they glowed with an eerie yellow glow. It is possible, but you will need to experiment and know what you can get away with for the construction.
You need to protect the LEDs from heat (since sculpey is oven fired) - because heat kills them and the leads WILL conduct heat into the circuit that makes them up.
|
I'm OVER 50 (and so far over everyone's BS, too).
Old enough to know better, young enough to not give a ****.
That is not dead which can eternal lie ...
... and yet, with strange aeons, even death may die.
|
|
|
|
2017/09/23 14:56:16
Subject: Re:Translucent Sculpey & LED's
|
|
Longtime Dakkanaut
|
I do not have a tutorial, but I generaly do my LED work in a string using a 9volt battery (the one with the two buttons on top, I find these the easiest to buy and hook up leads to. I have tried watch batteries and they never put out enough for what I want, although I am NOT an electrician or anything). Four to six LEDS seems to be the right number, although at times I have placed a resistor in. Straight loop wire, battery to switch, switch to string of LED's, to optional resistor, to battery. I just posted a lighted Hellbrute. He is a string of 3 lights, no resistor. This may be obvious so don't take offense, but the LED's I buy do have a pos/neg side, so must be strung correctly and not backwards. Generally a test run with the wires just twisted together works for this.
I have no experience with lighting sculpey, so sorry.
|
Keeping the hobby side alive!
I never forget the Dakka unit scale is binary: Units are either OP or Garbage. |
|
|
|
|