Switch Theme:

How not to build a Karist temple  [RSS] Share on facebook Share on Twitter Submit to Reddit
»
Author Message
Advert


Forum adverts like this one are shown to any user who is not logged in. Join us by filling out a tiny 3 field form and you will get your own, free, dakka user account which gives a good range of benefits to you:
  • No adverts like this in the forums anymore.
  • Times and dates in your local timezone.
  • Full tracking of what you have read so you can skip to your first unread post, easily see what has changed since you last logged in, and easily see what is new at a glance.
  • Email notifications for threads you want to watch closely.
  • Being a part of the oldest wargaming community on the net.
If you are already a member then feel free to login now.




Made in nl
Sure Shot Scarecrow Sniper






How not to build a Karist water temple



What follows is a brief overview of how I built this Karist temple (of which there are more pics in my gallery or painting thread linked to in my signature), inspired by the stepwells seen most commonly in India. A couple mostly water-related things did not work out at first, so here’s how to avoid those things.



1. I took the lid from one of those boxes they put wine bottles in, measured things, and glued my foam stairs to the lid. The steps are sized to accommodate normal 25mm based dudes without them tipping over. At the back: I just used scraps of foam to hold everything up. I then used foam again to make the basin.



2. I then stacked bits of foam to create the rock around the stairs and the temple entrance.



3. With fingers, a hobby knife, a serrated knife and a hot soldering iron I shaped the foam to look like rock.



4. I then undercoated the whole thing with white textured wall paint. Next, I used a hobby paint mixture to make everything rocky a yellow-sandish colour. The inside of the basin was painted a bright blue. The rock was then washed in diluted brown paint and the water area highlighted with progressively lighter shades of blue-green (lighter towards edges). The rock was highlighted with probably the base colour again and then adding in a sandy colour and white. I also used various coloured washes (reds, greens, browns) to give the rock colour some variation. All highlighting is simple drybrushing/overbrushing. In the last picture, I’ve poured Woodland Scenics E-Z water in the basin and in the water source on top, which is a resin you melt before pouring. This is the first thing you should not do. This stuff was just not suitable for this purpose. It shrunk and cracked as it cured and had a yellowish tint.



5. It’s not at all easy to remove E-Z water once it’s set, especially if you want to keep the surrounding terrain in one piece. Getting rid of it involved trying all sorts of methods, eventually a chisel was most effective. I then tried a more familiar (to me) product, which is Woodland Scenics Realistic water. This is awesome stuff and gave me a very nice pool. For the water drop and a little ripple effect I used Woodland Scenics Water effects, which is also nice.

Then I did the second thing you should not do. I figured I could add some white to the water by mixing white paint into the Water effects stuff and applying it where appropriate. However, Water effects itself is white until it cures, hence I couldn’t see how much the white paint coloured the Water effects. Of course, I didn’t bother to test my batch (all this water stuff takes forever to cure and I have no patience). Turns out I used too much white paint and all my water now looked ridiculous (basically like that picture of the uncured Water effects). The thing is, it’s impossible to get rid of. I think I tried painting over the whole thing? Not sure. Anyway, in the end I decided it was time to once again dig out the whole basin.

This time was worse, as the Realistic water isn’t as easily chiselled as the E-Z Water. It stays a little soft. After much perseverance I got everything out, but I destroyed some of the paint job and actual foam bits around the basin. I had to redo all that and also build new steps into the water (round steps this time). Now that I knew what not to do, again using Realistic water and Water effects got me the desired result (still room for improvement, but I’ll leave that for another project).



6. The final steps were making temple doors with the Karist logo out of plasticard, and detailing. The Maelstrom's Edge terrain sprue supplied a control panel. The doors were painted brown, then bronze, then drybrushed pewter and silver. The logo got various purple paints, washes and highlights. I used green weathering powder to colour the rock a bit in the crevices and then sprinkled on fine blended green turf for some moss, and the dried contents of some teabags around the edges of the basin to represent fallen leaves and such muck accumulating there. This muck, of, course, didn’t appear wet so I added a final coat of Realistic water (this is the white sheen you see in the last image). The colour from the tea bled a bit more than I’d like, so this is probably another thing I’d find a better procedure for next time. To finish up I glued some coarser, darker green turf to the rock to represent vines, washed that with a brown wash and then highlighted with an olive colour. I then broke a skewer in two and wrapped the ends in narrow masking tape to make two torches and planted these near the entrance, painted brown and metallic.

And that’s basically it! Apart from messing around with the water a lot (this cost me so much time, it ain’t funny), it’s a fairly simple project.

   
Made in us
Legendary Master of the Chapter





SoCal

Well, it looks great. Evocative and tranquil.

   
Made in gb
Hulking Hunter-class Warmech





Bristol, England

This is very awesome! Love the final water effects even if it took a couple of tries. Very helpful advice too.

Read the first two novels in the Maelstrom's Edge Universe now:

Maelstrom's Edge: Faith - read a sample here!

and

Maelstrom's Edge: Sacrifice 
   
Made in au
[MOD]
Making Stuff






Under the couch

Always nice when something goes horribly wrong and you manage to fix it

Great article.

 
   
Made in us
Last Remaining Whole C'Tan






Pleasant Valley, Iowa

Really great article. I'm just dipping my toe into water effects, so your missteps were really useful for me. It's a great looking piece.

This message was edited 1 time. Last update was at 2017/11/27 23:24:23


 lord_blackfang wrote:
Respect to the guy who subscribed just to post a massive ASCII dong in the chat and immediately get banned.

 Flinty wrote:
The benefit of slate is that its.actually a.rock with rock like properties. The downside is that it's a rock
 
   
Made in nl
Sure Shot Scarecrow Sniper






Thanks guys!

   
Made in us
Stealthy Warhound Titan Princeps







That is a really unique terrain piece, and the final water looks great!
   
Made in in
[MOD]
Otiose in a Niche






Hyderabad, India

A ton of hard work but the results were worth it!

 
   
Made in nl
Sure Shot Scarecrow Sniper






Thanks guys! I'm actually planning on integrating the temple and also the underground outpost into an entire table.



Fresh start



Basic plan

Lord knows when I'll finish it.

   
 
Forum Index » Maelstrom's Edge General Discussion
Go to: