| Author |
Message |
 |
|
|
|
|
Advert
|
Forum adverts like this one are shown to any user who is not logged in. Join us by filling out a tiny 3 field form and you will get your own, free, dakka user account which gives a good range of benefits to you:
- No adverts like this in the forums anymore.
- Times and dates in your local timezone.
- Full tracking of what you have read so you can skip to your first unread post, easily see what has changed since you last logged in, and easily see what is new at a glance.
- Email notifications for threads you want to watch closely.
- Being a part of the oldest wargaming community on the net.
If you are already a member then feel free to login now. |
|
 |
2014/03/21 00:07:00
Subject: Got a bit too much Tamiya putty on miniature, how to correct?
|
|
Been Around the Block
|
Hi guys, I was assembling a plastic model and used Tamiya putty to try and fill up the gaps between the pieces, but its my first time using the putty and I ended up getting a bit too much on the model and it got onto some of the exterior detail. Tried getting it off, but it dried pretty fast and now some excess is stuck on the model.
I was wondering if anyone has any advice on how to correct the issue, will just using an x-acto knife to carefully chisel away some of the excess be best or should I try and remove the putty and start from scratch?
If removing it is best, then what method? Will simple green or nail polish remover work? Or will it require some other method?
|
|
|
|
 |
|
2014/03/21 01:22:20
Subject: Got a bit too much Tamiya putty on miniature, how to correct?
|
|
Colonel
This Is Where the Fish Lives
|
 Avinash_Tyagi wrote:Hi guys, I was assembling a plastic model and used Tamiya putty to try and fill up the gaps between the pieces, but its my first time using the putty and I ended up getting a bit too much on the model and it got onto some of the exterior detail. Tried getting it off, but it dried pretty fast and now some excess is stuck on the model.
I was wondering if anyone has any advice on how to correct the issue, will just using an x-acto knife to carefully chisel away some of the excess be best or should I try and remove the putty and start from scratch?
If removing it is best, then what method? Will simple green or nail polish remover work? Or will it require some other method?
Scrape it off with a knife or you can sand it down with some fine-grit sandpaper.
|
 d-usa wrote:"When the Internet sends its people, they're not sending their best. They're not sending you. They're not sending you. They're sending posters that have lots of problems, and they're bringing those problems with us. They're bringing strawmen. They're bringing spam. They're trolls. And some, I assume, are good people."
|
|
|
|
|
2014/03/21 02:25:53
Subject: Got a bit too much Tamiya putty on miniature, how to correct?
|
|
Been Around the Block
|
Thanks, I took my knife to the putty and most came off without damaging the plastic, only a small amount remains now, I think its good enough to prime.
Is the small grit sandpaper safe for plastic minis?
|
|
|
|
|
|
2014/03/21 02:27:05
Subject: Got a bit too much Tamiya putty on miniature, how to correct?
|
|
Perfect Shot Dark Angels Predator Pilot
|
Could have a go with en emery board. The super fine side.
|
For the Lion and Terra!
Because nothing in the galaxy is black and white, Mankind views the Space Marines as a last resort. The last line. When all else fails. They take up the burden. The noble defenders of Mankind. The last hope.
With finecast you can bypass the washing stage and throw them straight into the bin.
Or cut out the middleman and just flush some money down the toilet.
-Chromedog |
|
|
|
|
|
|
